1/4" NPT Female Weld Bung Aluminum
Pack of 4
1/8" NPT Female Weld Bung Aluminum
1/2" Thick Cast Stainless Steel Flanges then final machined. This flange has threaded M8x1.25 holes commonly used on the inlet side of the wastegate when making manifolds.
AGP Turbo 38 / Tial 35 / Tial 38 / Turbonetics Evolution / Deltagate /...
1/2" Thick Cast Stainless Steel Flanges then final machined. This flange has through holes commonly used on the outlet side of the wastegate when making dump tubes.
AGP Turbo 38 / Tial 35 / Tial 38 / Turbonetics Evolution / Deltagate / TurboSmart...
.027" Thick Stainless Steel Gasket stamped OE style. Get rid of those composite gaskets that blow out every few months, and upgrade to something that actually works.
AGP Turbo 38 / Tial35 / Tial 38 / Turbonetics Evolution / Deltagate /...
This heatshield is designed to fit on the T31 style 4 bolt turbine housings from AGP, Garrett and Turbonetics. This heatshield attaches between the turbine outlet and the exhaust system. The heatshield is available in standard finish or highly polished.
For factory or aftermarket turbos on the stock DSM manifold
Turbine outlet gasket for the Garrett T31 Ballistic Concepts 4 bolt outlet turbocharger. The industry has adopted this flange pattern so AGP, Precision, and some Turbonetics housings use this same pattern. The ID for this patter is 2.5". This...
3/8" thick. Turbine outlet flange for the Garrett GT Ball Bearing turbocharger 3" outlet. GT30R, GT35R This is not the same flange as the T31. Bolt spacing is different.
Turbine outlet copper gasket for the Garrett GT Ball Bearing turbocharger 3" outlet. GT30R, GT35R This is not the same gasket as the T31. Bolt spacing is different.
3/8" thick. Turbine outlet flange for the T31 Garrett Ballistic Concepts 4 bolt outlet turbocharger. TA34
Adapt the V-Band compressor outlet of your GT42/45/47 and S400 based turbos to a 3" weld flange adapter with one of our kits. Kit includes V-Band clamp and CNC aluminum V-Band for you to weld a 3" tube
Have you always wanted to recirculate your HKS SSQ Blow off Valve? Here is an adapter tube that attaches to the end of the HKS Super Sequential that allows the vented air to be re-routed back into the intake. The tube is made from billet 6061 aluminum...
Aluminum blow off valve mounting flange for the HKS Super Sequential BOV radiused for 2.5" tubing.
Garrett GT25, GT28, GT30, and GT35 Ball Bearing Turbocharger Billet Aluminum Drain Flange with 1/2" NPT threads.
Billet aluminum T3/T4 Oil drain flange tapped for 1/2" NPT fitting. NOTE: These will also fit the Borg Warner S200 and S300 series turbos.
This is the fitting that screws into the T3 T4 S200 S300 Drain Flange to allow you to adapt to 3/4" ID Hose for the oil drain. 1/2" NPT to 3/4" Hose
Billet 6061 oil drain flange for Borg Warner S400. Center hole is tapped 3/4" NPT
This is the fitting that screws into the S400 Drain Flange to allow you to adapt to 3/4" ID Hose for the oil drain. 3/4NPT to 3/4" Hose
This oil drain gasket is used for GT25/GT28/GT30/GT35 ball bearing turbos as well as the GTX25, GTX28, GTX30, and GTX35. This can also be used for the oil feed gasket for certain turbos that have a flange style oil feed port.
Oil Drain Gasket for S400 and GT42-45-47 framed turbos
Oil Drain gasket for T3 and T4 bearing housings as well as S200 and S300 turbos.
This is the oil feed flange for T3, T4, and Bog Warner S200/S300 bearing housings. If you don't know what threads your oil feed port is, or if your oil feed port does not have threads, this flange will allow you to use an 1/8" NPT thread.
So you just bought this turbo from your "buddy" and you just can't figure out what the threads are. You've gone to the auto parts stores, home improvement stores, and you just can't get the correct one. Save the hassle and just buy this kit...